2WCOM DAB-4c

About

This is a DataMiner connector for the 2WCOM DAB-4c, a converter device that can be used to receive data signals from legacy ETI and EDI multiplexers while simultaneously converting the signals to EDI/ETI transmitters.

Configuration

Connections

SNMP Connection - Main

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP CONNECTION:

• IP address/host: The polling IP or URL of the destination.
• IP port: The IP port of the destination.

SNMP Settings:

• Get community string: The community string used when reading values from the device (default: public).
• Set community string: The community string used when setting values on the device (default: private).

SNMP Connection - Redundant

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP CONNECTION:

• IP address/host: The polling IP or URL of the destination.
• IP port: The IP port of the destination.

SNMP Settings:

• Get community string: The community string used when reading values from the device (default: public).
• Set community string: The community string used when setting values on the device (default: private).

Web Interface

The web interface is only accessible when the client machine has network access to the product.

How to use (1.2.3.x and 1.3.0.x range)

The Converter Overview page displays an overview of the available converters in the Converter Overview table for the EDI-to-ETI/EDI and ETI-to-EDI modes.

The EDI to ETI/EDI page displays input sources, source assignment, and ETI output data for the EDI-to-ETI/EDI mode.

The ETI to EDI page displays input sources, source assignment, and IP EDI output data for the ETI-to-EDI mode.

How to use (earlier ranges)

General

On this page, you can monitor and configure the system's Name, Location, and Contact. You can also monitor details related to the hardware and software versions running on the device.

The page contains page buttons to the following subpages:

• Details: Displays additional details related to the device.
• Diagnostic: Allows you to configure and monitor the Diagnostic Report module.
• Licensing: Displays detailed information about the licensing of the device.
• Settings: Allows you to configure additional global device settings.

Interfaces

This page provides all information about the available interfaces.

Converter Overview

This page displays an overview of the available converters in the Converter Overview table, as well as the EDI-EDI or ETI-EDI Outputs status.

Input Sources

This page displays an overview of the input and output sources.

GPI

This page displays the state of the GPI interfaces and allows you to switch sources or invert masks of each interface.

GPO

This page displays the state of the GPO interfaces and allows you to switch sources of each interface.

Network

This page contains the general configuration of the CTRL, Data 1, Data 2, and Ember interfaces.

The page contains page buttons to the following subpages:

• LAN CTRL: Contains the parameters related to the configuration of the CTRL interface.
• LAN: Allows you to configure LAN CTRL built-in device alarm monitoring conditions.
• Data 1: Contains the parameters related to the configuration of the Data 1 interface.
• Data 2: Contains the parameters related to the configuration of the Data 2 interface.

DNS

This page allows you to monitor the DNS Server Configuration.

SNMP

On this page, you can monitor and configure SNMP settings, as well as the SNMP trap servers.

Time

This page contains the NTP and time zone configuration.

Via the External NTP page button, you can configure built-in device alarm monitoring conditions for external clock NTP and NTP Calibration.

Via the NTP page button, you can configure built-in device alarm monitoring conditions for System NTP.

User

On this page, you can configure user accounts and the access to these accounts.

Device Hardware

This page provides an overview of the device status, including the CPU/Device Temperature, CPU Load, and Power Supply Unit Parameters, along with other generic monitoring parameters.

• PSU: Allows you to configure PSU 1 and PSU 2 built-in device alarm monitoring conditions.
• Temp: Allows you to configure Temp built-in device alarm monitoring conditions.

Converter Alarms

This page displays the built-in device alarm states for Converters Packet Loss Rate (PLR) and Output Errors.

It also contains page buttons to subpages where these alarms can be configured:

• EDI Input 1: Allows you to configure EDI Input 1 built-in device alarm monitoring conditions for each converter.
• EDI Input 2: Allows you to configure EDI Input 2 built-in device alarm monitoring conditions for each converter.
• ETI Inputs: Allows you to configure ETI Input built-in device alarm monitoring conditions for each ETI input.
• Inputs: Allows you to configure Inputs built-in device alarm monitoring conditions for each converter input, EDI-to-EDI2 input, and ETI-to-EDI 2 input.
• ETI Outputs: Allows you to configure ETI Output Error built-in device alarm monitoring conditions for each ETI output.

Log

This page displays the configuration of the built-in device system log.