Audemat Aztec Goldeneagle FM
With this connector, information can be gathered and viewed from the device Audemat Aztec Goldeneagle FM. The connector also allows you to configure the device to an extent.
About
This connector is used to gather information from the Audemat Aztec Goldeneagle FM device.
Version Info
| Range | Description | DCF Integration | Cassandra Compliant |
|---|---|---|---|
| 1.0.0.x | Initial version | No | No |
| 2.0.0.x | New firmware | No | Yes |
| 2.1.0.x | Added support for device firmware 10.9.0. | No | Yes |
Product Info
| Range | Supported Firmware Version |
|---|---|
| 1.0.0.x | 8.5 |
| 2.0.0.x | 10.8 |
| 2.1.0.x | 10.9.0 |
Installation and configuration
Creation
SNMP main connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP Address/host: The polling IP of the device.
SNMP Settings:
- Port number: The port of the connected device, by default 161.
- Get community string: The community string in order to read from the device. The default value is public.
- Set community string: The community string in order to set to the device. The default value is private.
HTTP Connection
This connector uses an HTTP connection and requires the following input during element creation:
HTTP CONNECTION:
- IP address/host: The polling IP of the device.
- IP port: The IP port of the destination.
- Bus address: If the proxy server has to be bypassed, specify bypassproxy.
Usage (1.x.x.x)
General Page
This page displays general parameters of the Audemat Aztec Goldeneagle FM device, such as the Device Name, Software Version, Device Serial Number and Device Status.
This page also contains the page buttons Trap Config, Email Config, Events Config, Modules, Hardware Version, Software Version, and Webcam.
The page also contains buttons to Initialize and Reset Device.
Channels Configuration
This page displays a table with all available channels and their configuration.
It also contains the page buttons Pilot Monitoring, AF Monitoring, RF Monitoring, Transmission Alarm, White Noise Monitoring, Extended RDS Monitoring, RDS Monitoring, MPX Monitoring and Channel ID Watch.
Measurement
This page displays a table with all the measurements for the channels.
Commands
This page contains parameters that can be used to send commands to the device, for example to erase a video or audio file, or to perform a manual scan.
It also contains the page button Channels Auto Configuration and the buttons RDS Sync, Take Snapshot and Get In/Out Status.
Scanning
This page allows you to set the scanning configuration.
Recording
This page allows you to set the recording configuration.
It also contains the page button Recordings, which displays the existing audio recordings.
Audio Tag
This page allows you to set the audio tag configuration.
It also contains the page button Tag Configurations, which displays the existing tag configurations.
Web Interface
This page shows the web interface of the device. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.
Usage (2.x.x.x)
General Page
This page displays general parameters of the Audemat Aztec Goldeneagle FM device, such as the System Name, Software Version, CPU Temperature and Serial Number.
The page also displays the Channels table, which displays all configured FM channels.
It also contains the following page buttons:
- SNMP Configuration: Allows you to configure the SNMP parameters, such as the SNMP Manager Address, Trap Version and Local Agent Port.
- Email Configuration: Allows you to configure the Email Address of the main recipient and two copy recipients.
Carriers
This page shows a tree view with all available channels and their measured values.
The page also contains a page button that displays the raw data used to build the tree view.
Alarms
This page shows a tree view with all available channels and their alarm values.
The page also contains a page button that displays the raw data used to build the tree view.
Tuner
This page shows the current Tuner Status. It also allows you to Start and Stop Streams.
Web Interface
This page shows the web interface of the device. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.