Table of Contents

Axon ACP U4T200

The U4T200 is 4K (4-wire) production toolbox. It has an audio de-embedder and embedder with full audio shuffling. It also does LUT-based color space and dynamic range conversion.

The Axon ACP U4T200 connector is used to monitor this card.

About

Version Info

Range Key Features Based on System Impact
1.0.0.x [SLC Main] Initial version - -

Product Info

Range Supported Firmware
1.0.0.x 2129, 2233, 2435, 2536

System Info

Range DCF Integration Cassandra Compliant Linked Components Exported Components
1.0.0.x Yes Yes - -

Configuration

Connections

Serial Main Connection

This connector uses a serial connection and requires the following input during element creation:

SERIAL CONNECTION:

  • Interface connection:

    • IP address/host: The polling IP or URL of the destination.
    • IP port: The IP port of the destination (fixed value: 2071).
    • Bus address: The bus address or slot number/position of the card in the frame.

Serial IP Connection - Broadcast Connection

This connector uses a smart-serial connection and requires the following input during element creation:

SMART-SERIAL CONNECTION:

  • Interface connection:

    • IP address/host: The polling IP or URL of the destination.
    • IP port: The IP port of the destination (fixed value: 2071).
    • Bus address: The bus address or slot number/position of the card in the frame.

How to use

The setting of some parameters depends on other parameters' current value. For example, on the Network page, in order to set the Preferred IP Address, you need to make sure the IP Configuration is set to Manual mode. When such a parameter is not set to the correct value, a message box will be displayed. Follow the instructions in the message box and set the required parameter to the appropriate value before setting the other parameter.

DataMiner Connectivity Framework

The 1.0.0.x connector range of the Axon ACP U4T200 connector supports the usage of DCF.

DCF can also be implemented through the DataMiner DCF user interface and through DataMiner third-party connectors (for instance a manager).

Interfaces

Fixed interfaces

Physical fixed interfaces:

  • SDI Input 1: A single fixed interface of type in.
  • SDI Input 2: A single fixed interface of type in.
  • SDI Input 3: A single fixed interface of type in.
  • SDI Input 4: A single fixed interface of type in.
  • SDI Output 1: A single fixed interface of type out.
  • SDI Output 2: A single fixed interface of type out.
  • SDI Output 3: A single fixed interface of type out.
  • SDI Output 4: A single fixed interface of type out.

Connections

Internal Connections

  • SDI Input 1 -> SDI Output 1.
  • SDI Input 1 -> SDI Output 2.
  • SDI Input 1 -> SDI Output 3.
  • SDI Input 1 -> SDI Output 4.
  • SDI Input 2 -> SDI Output 1.
  • SDI Input 2 -> SDI Output 2.
  • SDI Input 2 -> SDI Output 3.
  • SDI Input 2 -> SDI Output 4.
  • SDI Input 3 -> SDI Output 1.
  • SDI Input 3 -> SDI Output 2.
  • SDI Input 3 -> SDI Output 3.
  • SDI Input 3 -> SDI Output 4.
  • SDI Input 4 -> SDI Output 1.
  • SDI Input 4 -> SDI Output 2.
  • SDI Input 4 -> SDI Output 3.
  • SDI Input 4 -> SDI Output 4.

Notes

This connector is best combined with the Axon ACP Frame Manager connector but can be used as a standalone connector as well.

In the Connections section above, all the possible input/output combinations for the internal connections are listed. This means that, for example, SDI Input 1 can be connected to SDI Output 1 or 2 or 3 or 4. If the device allows simultaneous connection of one input to more than one output, that is also an option.

Improve this page