CEFD CDD-S2 SNMP
The Comtech EF Data CDD-S2 provides high-performance satellite-based communication solutions for a diverse range of applications.
About
The CEFD CDD-S2 connector is used to monitor and control a CEFD CDD-S2 device. The information is displayed in different pages regarding a certain category and there is the possibility to modify the settings. This connector uses SNMP to retrieve and configure the device's data.
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x | Initial version | - | - |
| 1.0.1.x [SLC Main] | Multiple tables now uses naming instead of displayColumn to make the database for these tables Cassandra-compliant. | 1.0.0.9 | Old trend data will be lost for these tables. |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | Unknown |
| 1.0.1.x | Unknown |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | No | - | - |
| 1.0.1.x | No | Yes | - | - |
Installation and configuration
Creation
SNMP connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: the polling IP of the device, e.g., 10.11.12.13
- Device address: not used
SNMP Settings:
- Port number: The port of the connected device, default: 161
- Get community string: The community string used when reading values from the device. The default value is public.
- Set community string: The community string used when setting values on the device. The default value is private.
Usage
General page
The General page displays the System Information, Service Contact information and the Overall Status of the device.
Admin page
The Admin page displays the selected configuration and options. There is the possibility to set the SNMP Trap Destination IP Address and the Auto Logout Time.
Also there is a page button available that will open a pop-up page which displays additional information regarding the subject stated on the page button.
Configuration - Interface Page
This page displays the Interface Table.
Configuration - WAN - Demod Page
First of all the Demodulator table is viewable on this page. Underneath there are two groups of settings available:
- Automatic Demod Configuration Switch: settings for the switch can be set,
- Receive WAN Labels: the user can set each label to a value between 1 and 2047, if an arriving packet matches the value of the label, then the packet is processed, otherwise it is filtered.
Configuration - WAN - LNB Page
On this page the settings and the status for the LNB Control can be viewed/set.
Configuration - WAN Page
The user can set each Receive WAN label on this page, to a value between 1 and 2047, if an arriving packet matches the value of the label, then the packet is processed, otherwise it is filtered.
Configuration - Network Page
The Configuration - Network page displays the Routing and ARP table. The user can create new entries by clicking on the Create New Entry page button and fill in the required field on the pop-up page. The IGMP can be viewed and set when the user clicks the IGMP page button.
Status - Status pages
Each of these Status - Status - x pages will display the status for the subject in the page name.
Status-Monitor pages
The Status - Monitor pages are used to monitor the system, Alarms and the Events.
On the Status - Monitor - Alarms page there is the possibility to mask the alarms by going to the pop-up pages of this page and setting the Mask parameters for each one to Enabled.
Utility Page
On the Utility page the settings for the Modem and Save/Load Configuration can be set/viewed.
The status of the Memory Usage can be viewed by clicking on the Diagnostic page button.
Utility - BERT/Redundancy Page
This page the settings for the BERT, Console and the Satellite can be set.
The status of the Redundancy and the Monitoring of the BERT can also be viewed.
FKS page
In this page it is possible to set the FSK functionality. This functionality will generate a virtual element that contains all LNB parameters. A unique FSK Element Name can be set for the virtual element.
Traps page
On the Traps page the incoming traps can be viewed in the Traps table.
FTP page
On the FTP page the FTP table can be viewed.
Web Interface page
Here the web interface of the device can be viewed. The client machine has to be able to access the device. If not, it won't be possible to open the web interface.