CISCO ASR Manager
This is an SNMP connector that is used to monitor and configure the CISCO ASR Manager equipment.
About
Version Info
| Range | Description | DCF Integration | Cassandra Compliant |
|---|---|---|---|
| 1.0.0.x | Initial version. | Yes | Yes |
| 1.0.1.x [Obsolete] | Added "IF Translation Table". | Yes | Yes |
| 1.0.2.x [Obsolete] | Changed display key for interface detail tables. | Yes | Yes |
| 1.0.3.x [Obsolete] | Removed some parameters from the SSH page that were made irrelevant by the reworked SSH system. | Yes | Yes |
| 1.0.4.x [SLC Main] | Changed the type of some PTP parameters from string to numeric text. | Yes | Yes |
| 2.0.0.x [Obsolete] | DCF tables added. | Yes | No |
| 2.0.1.x | Fixed Cassandra compliancy. | Yes | Yes |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | Cisco IOS Cisco IOS XR |
| 1.0.1.x | - |
| 1.0.2.x | - |
| 1.0.3.x | - |
| 1.0.4.x | - |
| 2.0.0.x | - |
| 2.0.1.x | - |
Configuration
Connections
SNMP Main Connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device.
SNMP Settings:
- IP port: The IP port of the device.
- Get community string: The community string used when reading values from the device, by default public.
- Set community string: The community string used when setting values on the device, by default private.
Additional requirement from version 1.0.1.18 onwards
From version 1.0.1.18 of the connector onwards, the custom DLL "Renci.SshNetSLC.dll" is required.
Usage
General
This page displays the System Name, System Description, System Location, System Contact, System Up Time, and other general parameters.
You can also enable or disable the polling of some of the tables of the connector here.
Detailed Interface Info
This page displays the Detailed Interface Info table.
The page also contains a button that can be used to Remove Unused Interfaces from the Detailed Interface Info table.
Via Measurement Configuration, you can enable or disable the polling of interface communication KPIs:
The Enable All button enables polling for all the interface communication KPIs.
The Disable All button disables polling for all the interface communication KPIs.
The Enable Oper. Up button enables polling for all interface communication KPIs with an Up operation state, and it disables all with a Down or Admin Down operation state.
The Keep and Enable Oper. Up button enables polling for all interface communication KPIs with an Up operation state, and it disables all with an Admin Down operation state.
Detailed Interface Info - Rx
This page displays the Detailed Interface Info - Rx table.
Detailed Interface Info - Tx
This page displays the Detailed Interface Info - Tx table.
PoE
This page displays the PoE and Workgroup table.
ISDN
This page displays the IDSN-related information.
BGP
This page displays the BGP Peer table and other BGP-related information.
HSRP
This page displays the HSRP Group table.
LDP
This page displays the LDP table.
OSPF
This page displays the OSPF-related information.
IGMP
This page displays the IGMP Interface and IGMP Cache table.
IPSec
This page displays the IPSec Phase 1 Peer State and IPSec Phase 1 Tunnel and IPSec Phase 2 Tunnel table.
IP SLA
This page displays the IP SLA table.
QoS
This page displays the QoS tree view information.
Hardware Info
This page displays the Ent Physical table.
Fan - PS Info
This page displays the Fan Tray Status and FRU Power Status table.
Sensor
This page displays the Ent Sensor Value table.
VLAN Info
This page displays the VLAN Info table.
PIM
This page displays the Interface, Neighbor, and IP Multicast Route (PIM) table.
ISIS
This page displays the ISIS system-related information.
EIGRP
This page displays the VPN, Traffic Statistics, Topology, Peer, and Interface (EIGRP) table.
VRF
This page displays the CSV VRF, VRF (CV), and VRF Interface (CV) table.
VRF Interface Tree
This page displays the VRF Interface tree view information.
MPLS VPN
This page displays the MPLS VPN Interface Configuration, MPLS VPN VRF, and MPLS VPN VRF Route table.
VRF Tree
This page displays the VRF tree view information.
Process
This page displays the Process-related information.
SSH
This page allows you to send commands over SSH. Two types of authentication are available:
- Default: Uses the password to establish the connection.
- Keyboard Interactive Authentication: If this mode is selected, the connector simulates the entry of the password on the keyboard to allow successful authentication with the device. Some devices enforce this type of authentication for security reasons.