CISCO D9859
This connector has control/monitoring purposes. The Cisco D9859 device is an Advanced Receiver Transcoder that allows to deliver MPEG-4 HD services to MPEG-2 CATV headends.
About
This is an SNMPv2 connector. Traps can be retrieved if they are enabled on the device.
Version Info
| Range | Description | DCF Integration | Cassandra Compliant |
|---|---|---|---|
| 1.0.0.x | Initial version | Yes | Yes |
Product Info
| Range | Supported Firmware Version |
|---|---|
| 1.0.0.x | 1.11 |
Installation and configuration
Creation
SNMP Main connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device (e.g., 172.16.8.123).
- Device address: Not required.
SNMP Settings:
- Port number: The port of the connected device (e.g., 161).
- Get community string: The community string used when reading values from the device (e.g., public).
- Set community string: The community string used when setting values on the device (e.g., private).
Usage
Summary
On this page, you can find the: Audio Status Table, Video Status Table, Program Entry Status Table and the Program Entry PID Table.
The About ... page button gives access to product parameters such as the About Current Version, About Safe Version, About Product ID, About App Table, ...
In the DSG About ... page button, the SW Table and Firmware Table can be found.
The Messages ... page button contains the Message Table.
Input
On this page you can find the following parameters: Active Tuning Input, Signal Lock Time, Verify Timer, Active Tuner Table, Satellite Signal Table, ...
In the SI Receive Setup page button, you can find the following tables: Input Status Table, SI RCV Option Table and SI RCV Option Status Table.
The Muting Thresholds ... page button contains the Muting Thresholds Table, and the Backupt Transport Table can be found in the Disaster Recovery Status ... page button.
The Channel Status ... page button contains the Program Entry Status Table and the Conditional Access ... page button, the CA ADP Table.
In the BISS ... page button the available parameters are; BISS Mode, BISS Mode 1 Session Word, BISS Mode-E Session Word, BISS Mode-E Injected ID.
In the Stream Details ... page button are the following tables displayed: SI Info RX Table, SI Info TS Table, SI Info VC Info Table, Program Entry PID Table.
Audio - Video
In the Video Decoding section, you can find the Video Control Table and the Video Status Table.
In the Subtitles ... page button of this section, subtitles related parameters are shown: Subtitles OP Mode, Subtitles Foreground, Subtitles Manual Entry, ...
In the same section, the VBI ... page button shows, among others: VBI VITS Flag 17, VBI VITS Flag 18, VBI VITS Flag 330, VBI VITS Flag 331, etc.
In the Audio Decoding section, you can find 2 tables: Audio CTRL Table and Audio Status Table.
2 page buttons are also available: Cueing ... and Decode Enables ...
In the Cueing ... page button, you can find the Cueing Tone, Cueing Relay Mode, Cueing Tone Sequence Table, etc.
The Decode Enables ... page button displays the Decode Table.
Transport Stream
This page contains the TS Out Table and the TS Out Status Table.
In the Digital Program Mapping ... page button, you can configure the device through the DPM Regenerate, DPM Configuration Table and DPM PID Map Table.
The Transport Stream ... page button contains the DPM Aligned PMT Table.
In the MoIP Streams ... page button, parameters such as the MoIP IP Output Stats HW Global Error or the MoIP IP Output Stats Stream Error are available. You can also find the MoIP IP Output Configuration Table and the MoIP IP Output Stream Status Table.
The Transcoder Setup ... page button contains the following information: Transcoder LOI Action, Transcoder Configuration Table, Transcoder Status Table and Transcoder Subtitle Table.
System Settings
On this page, you can find the Backup Set Table and a series of page buttons for specific settings.
In the Identification ... page button, you can find among others the MAC Info Table and the Feature Licence Table.
In the IP Settings ... page button, you can find parameters such as the IP Configuration Table, Protocols CTRL SSH, ETH Backup Status Table or Unicast Routes Table.
The Time/Clock ... page button contains the Time Format and Time GMT Offset.
In the Alarm Status ... page button, you have access to the AW Fault Active List Table.
The Alarm Setup ... page button contains the AW Fault Status Table and the AW Fault Setting Table.
The Alarms History ... page button shows the AW Fault History Table.
The Versions ... page button gives detailed information about the installed softwares through several tables (Firmware Version Table, ...).
This page button contains also a section were you can configure the App/License/FPGA downloads; it contains, among others, the Download TFTP Server IP, Download Code Version and Download TFTP Filename parameters.
The Settings File ... page button contains status/configuration parameters related to the settings file transfer via FTP. You can find here the Backup Restore Type, Backup Restore File Name, Backup Restore Last Restore Time and the Backup Restore Percentage Completed parameters, among others.
The Security/Accounts ... page button contains 2 sections: the Lock Level Settings and the Front Panel. In the Lock Level Settings section, you can edit the following parameters: Lock Level, Lock Level PWD, Lock Level Current PWD, Lock Level New PWD and Lock Level Confirm PWD. In the Front Panel section, the following parameters can be altered: FP UI KB Lock, FP UI KB Lock Timeout, FP UI LCD Contrast and FP UI AW Reminder.
Support
This page shows the Diagnostic CTRL History Table.
The Usage Counters ... page button contains the following information: Power On Creation Date, Power On Total Hours, Power On Factory Reset Count, ...
The Fans/Temperatures ... page button splits fans and temperatures measurements into 3 tables: Diagnostic Health Monitor Table, Diagnostic FAN RPM Table and Diagnostics ECC Readings Table.
The Alarm History ... page button contains the AW Fault History Table.
Miscellaneous
This page contains the Program Entry Table, the MPE Configuration Table or whether the DPM PE Mapping Table.
The CI ... page button contains inter alia, the CI Configuration Table and CI Program Decrypt Table.
In the SDI ... page button, you have access to, among others, the VANC Global Status Frames, VANC Global Status Words, VANC Configuration Table and SDI Audio Slot Table.
Web Interface
Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.