Harris Falcon III RF-7800W
The Harris RF-7800W High-Capacity Line-of-Sight (HCLOS) Radio provides secure, dependable wireless broadband connectivity for both military and commercial applications.
About
This connector is used to monitor the major parameters (inputs and outputs) of the device. The connector also contains an overview of the active alarms.
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [SLC Main] | Initial version. | - | - |
Product Info
| Range | Supported Firmware Version |
|---|---|
| 1.0.0.x | V 5.00 |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | No | - | - |
Installation and configuration
Creation
SNMP Main Connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device.
SNMP Settings:
- IP port: The IP port of the device.
- Get community string: The community string used when reading values from the device, by default Public.
- Set community string: The community string used when setting values on the device, by default Private.
HTTP AntennaAlignment Connection
This connector uses an HTTP connection and requires the following input during element creation:
HTTP CONNECTION:
- IP address/host: The polling IP of the device.
- IP port: The IP port of the device.
- Device address: bypassproxy
Usage
General
This page contains the Web Interface of the vendor, as well as the following general information:
- The System section contains general info on the system, such as the System Name, System Details, System Location, etc.
- The Host section displays the Ethernet MAC Address, IP Address, IP Subnet Mask and Default Gateway Address of the host.
System Status
This page contains page buttons that provide access to the following subpages:
- Wireless System: Includes the Current Tx Power, Channel Frequency, DFS Action and Radio Temperature in degrees Celsius and Fahrenheit.
- GPS: Displays the GPS status and satellite coordinates info, as well as the Satellite Table.
- Redundancy: Displays the Redundancy Role, Peer IP, Timeout, etc.
- External Power Amplifier: Displays info related to Gain and Status.
- Wireless Ethernet Statistics: Includes the number of buffered and discarded packets (both Rx and Tx).
- Ethernet Port Statistics: Displays statistical info on the buffered and discarded packets at the Ethernet interface.
- EIM: Displays information on Enhanced Interference Mitigation, including EIM Channel Change Status, Interference Detected and Relative Noise Floor.
- SW Upgrade Status: Displays the firmware download status, the TFTP Server Address and the Download TFTP Address Type.
Links Summary
This page displays the Subscriber Links Summary table. Polling for the table can be enabled or disabled with the option Links Summary Table Polling.
Antenna Alignment
This page displays information regarding the antenna alignment, received via HTTP, namely RSSI 1, RSSI 2, SNR 1 and SNR 2.
Configuration - System
This page contains several different sections of configurable system settings:
- System Identification: Includes the System Name, System Location and System Contact.
- SW Upgrade Config: Includes TFTP info.
- Basic Host Configuration: Includes the IP Address, Subnet Mask and Default Gateway Address settings.
- Advanced Host Configuration: Includes the Ethernet Port Mode, SNTP Server IP Address, Time Zone (GMT) [Hh:mm], HTTP Access, Telnet Access and Telnet Port.
- Miscellaneous System Configuration: Allows you to enable or disable the GPS Antenna Power Supply and set the GPS Coordinates Format.
- Redundancy Config: Contains the settings for Role, Peer IP and Timeout.
Configuration - Wireless
This page allows you to change settings related to the wireless interface:
- Basic Wireless Configuration: Includes the System Mode Configuration, Channel Size, New RF Operating Frequency, Tx Power, Antenna Alignment Buzzer, and Radio Mode (which can be set to Off, RF Port 1, RF Port 2 or RF Port 1&2).
- Advanced Wireless Configuration: Includes the Maximum Distance in km and miles, DFS Action Config, Antenna Gain, External PA Present, Registration Period, Scheduling Cycle and ATPC Mode.
- Wireless Enhanced Interference Mitigation (EIM): Includes both SC and SS Interference Detection.
- External Power Amplifier Config
Configuration - File Management
This page displays the Active and Alternative Versions of the firmware and allows you to to activate the alternate version.
Broadcast/Multicast Configuration
This page displays the Broadcast/Multicast configuration.
Prioritization (1.0.0.5 and above)
This page displays the configuration for Prioritization Rules and Queue Policies on Link and Broadcast and Multicast.
Provisioning Subscriber Links
On this page, you can configure links displayed in the Subscriber Links Configuration Table.
Polling for this table can be enabled or disabled with the Subscriber Link Table Polling parameter. In the context menu of the table, a Poll Table option is also available.
Roaming Stranded (1.0.0.5 and Above)
On this page, you can configure the Roaming Stranded SC Check IP Address, IP Address Type and Status.
Trap
This page displays the Event Trap Table as well as the Total Events. The table displays all received traps related to the device, including BS Power Supply Status, BS Temperature Threshold, Password Change Failure, Firmware Config Failure, EEPROM Corrupted, Hardware Failure, DFS Event Trap, Modification in the Configuration of an ID, SW Upgrade Failed, SW Upgrade Success, GPS Number Used Satellites Low, GPS Number Used Satellites 12 h Low, PPS Not Available, etc.
Via the Config page button, you can configure automatic clearing of events from the Event Trap Table via the Maximum Number Traps parameter. You can also configure whether specific traps will be received using the Trap Activation Table and Up/Down Link Trap Table. Finally, this subpage also allows you to enable or disable SNMP Authentication Failure Traps.
Web Interface
This page allows the access to the SNMP device web interface. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.