Harris Flexiva10KW IRTFM Np1

About

With this connector, information can be gathered and viewed from the device Harris Flexiva10KW IRTFM Np1. The connector also makes it possible to set values on the device.

Version Info

Range	Description
1.0.0.x	Initial version
1.0.1.x	Added support for DVEs

Installation and configuration

Creation

SNMP main connection

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP CONNECTION:

IP Address/host: The polling IP of the device.

SNMP Settings:

Port number: The port of the connected device, by default 161.
Get community string: The community string in order to read from the device. The default value is public.
Set community string: The community string in order to set to the device. The default value is private.

Usage

General Page

This page displays general parameters of the Harris Flexiva10KW IRTFM Np1 device:

FNM Plus1 Local Mode
FNM Plus1 Control Unit Fault
FNM Plus1 Switch Over Ready
FNM Plus1 Switch Over Executed
FNM Plus1 Switch Over fault
FNM Plus1 Event Transmitter Index

The page also displays the following configurable parameters:

FNM Plus1 Redundancy Switch Over
FNM Plus1 Switch Over Mode
FNM Plus1 Channel Selection

Main Transmitter Page

This page displays parameters related to the Main Transmitter:

FNM Plus1 RTRF Program Present
FNM Plus1 RTOp Mode
FNM Plus1 Main Transmitter table

The table has two control buttons:

Refresh: Refreshes the table parameters.
Polling: Activates or deactivates the automatic polling of the table parameters.

Transmitter A Page

This page displays a table, the FNM Plus1 Transmitter A table, with information regarding Transmitter A. The table has two control buttons:

Refresh: Refreshes the table parameters.
Polling: Activates or deactivates the automatic polling of the table parameters.

Transmitter B Page

This page displays parameters related to Transmitter B:

FNM Plus1 TBRF Present
FNM Plus1 TB Local Mode
FNM Plus1 TB Fault
FNM Plus1 TB Warning

Traps Controller Page

This page allows the user to activate or deactivate the traps sent by the device. It includes the following parameters:

FNM Plus1 Redundancy Switch Over Enable
FNM Plus1 Local Mode Enable
FNM Plus1 Control Unit Fault Enable
FNM Plus1 Switch Over Mode Enable
FNM Plus1 Switch Over Ready Enable
FNM Plus1 Switch Over Executed Enable
FNM Plus1 Switch Over Fault Enable
FNM Plus1 Channel Selection Enable
FNM Plus1 Transmitter B Reset Enable
FNM Plus1 Transmitter B Mode Enable
FNM Plus1 RTOp Mode Enable
FNM Plus1 RTRF Program Present Enable
FNM Plus1 TBRF Present Enable
FNM Plus1 TB Local Mode Enable
FNM Plus1 TB Fault Enable
FNM Plus1 TB Warning Enable

This page also contains two page buttons, Main Transmitter. and Transmitter A., via which you can enable or disable the traps related to these transmitters.

Harris General Page

This page displays general information about the Harris device status:

Reserve Tx Status Dvr Input Ok
Reserve Tx Status Ps Sum Fault
Reserve Tx Status Ps Sum Warning
Reserve Tx Status Out Reflected Power
Reserve Tx Status Out VSWR

Harris Main Tx Table Page

This page displays the Main Tx Table. The table has two control buttons:

Refresh: Refreshes the table parameters.
Polling: Activates or deactivates the automatic polling of the table parameters.

The table contains the following columns:

Main Tx Ps Sum Fault
Main Tx Ps Sum Warning
Main Tx Monitor Mode

Harris Tx Status Table Page

This page displays the Main Tx Status Table. The table has two control buttons:

Refresh: Refreshes the table parameters.
Polling: Activates or deactivates the automatic polling of the table parameters.