Table of Contents

NTT Electronics HC11000D

About

The HC32000D is a K/60p HEVC 422 10bit multi-channel decoder, manufactured by NTT Electronics.

This connector allows you to view and control general and workflow (input, decode, output) settings of the device. These settings are retrieved and set via SNMP. SNMP traps, when enabled in the device, will update the list of alarms.

Product Info

Range Supported Firmware Version
1.0.0.x 3.1

Configuration

Creation

SNMP Main connection

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP CONNECTION:

  • IP address/host: The polling IP of the device.
  • Device address: Not required

SNMP Settings:

  • Port number: The port of the connected device, by default 161. Can be changed in the SNMP settings of the device.
  • Get community string: The community string used when reading values from the device. The default value is public.
  • Set community string: The community string used when setting values on the device. The default value is private.
Note

The device allows 10 SNMP communities to be configured on the SNMP settings page.

Web Interface

The web interface is only accessible when the client machine has network access to the product.

Usage

General

This page provides an overview of the general system information and status. It also allows you to perform a system reboot and change network settings.

The following subpages are available:

  • Network - Control: Allows you to configure the CTRL1 and CTRL2 network interfaces and view their status.
  • Network - Data: Allows you to configure the DATA1 and DATA2 network interfaces and view their status.
  • Network - SNMP: Allows you to configure and consult the SNMP settings (ports, community string, and traps).
  • Network - Syslog: Allows you to configure and consult the syslog target server settings.
  • Network - Monitoring: Allows you to configure and consult the monitoring target server settings.
  • Network - TCP: Allows you to configure and consult the TCP settings.
  • Network - PPoE: Allows you to configure and consult the PPoE settings.
  • Misc: Allows you to configure and consult buzzer volume, ID format, front panel, date and time, and NTP settings
  • Event Log: Allows you to configure and consult the event log level customization settings.

Alarms

This page provides a list of the current alarms. It also allows you to clear this list in the device.

Input

This page allows you to configure the IP stream settings of the device. The input stream can be selected, and the common stream settings can be configured.

On the Input - Status subpage, you can configure the settings of the first and second IP streams and the IP receiver.

Decoder

This page allows you to configure the decoder settings of the device. The program number and packet identifiers of the transport stream can be configured. It is also possible to change the video, audio, and genlock decoding settings, as well as the audio mapping.

The following subpages are available:

  • Decoder - Program Status: Provides an overview of the status info of the decoded stream, as well as a list of the available programs the stream.
  • Decoder - TS Stream - BISS: Allows you to configure the ancillary BISS.
  • Decoder - TS Stream - ID Status: Provides a status overview of the packet identifiers in use by the different output types.
  • Decoder - TS Stream - Audio: Allows you to configure the packet identifiers for each of the eight audio streams.
  • Decoder - TS Stream - Ancillary: Allows you to configure the packet identifiers for each of the four ancillary streams.
  • Decoder - TS Stream - Video Status: Displays the status information of the video stream.
  • Decoder - TS Stream - Audio Status: Displays the status information of each audio stream.
  • Decoder - TS Stream - Ancillary Status: Displays the status information of each ancillary stream.
  • Decoder - Audio: Allows you to change audio delay settings per audio stream.
  • Decoder - Audio Mapping: Allows you to map the audio stream channels to the embedded SDI audio channels.

Output Video

This page displays the current SDI output status and allows you to configure the video main and SDI level output settings.

Output Audio

This page allows you to configure the audio output settings.

Output Signal

This page allows you to configure the signal output settings.

Presets

This page allows you to load, save, protect, and delete configuration presets. A list of up to 64 presets can be maintained. The current preset is shown. A startup preset can be selected and the default preset can be loaded.

Web Interface

On this page, you can consult and manage the device through its web interface. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.

DataMiner Connectivity Framework

NTT Electronics HC32000D protocol supports the usage of DCF. DCF can also be implemented through the DataMiner DCF user interface and through DataMiner third-party connectors (for instance a manager).

Interfaces

Fixed interfaces

Physical fixed interfaces:

  • Data 1: Interface of type in based on Network Data 1 Link Status
  • Data 2: Interface of type in based on Network Data 2 Link Status
  • ASI: Interface of type in based on Input Signal ASI Status
  • SDI A: Interface of type out based on Video Output SDI Signal Status
  • SDI B: Interface of type out based on Video Output SDI Signal Status
  • SDI C: Interface of type out based on Video Output SDI Signal Status
  • SDI D: Interface of type out based on Video Output SDI Signal Status
  • ASI Output: Interface of type out.

Connections

Internal Connections

  • Between Data 1 and SDI A, SDI B, SDI C, SDI D, and ASI Output
  • Between Data 2 and SDI A, SDI B, SDI C, SDI D, and ASI Output
  • Between ASI and SDI A, SDI B, SDI C, SDI D, and ASI Output
Improve this page