Table of Contents

SYes PCM Television

The SYes PCM Television is a multistandard RF transmitter.

About

This is an SNMP connector for the SYes PCM Television device.

Version Info

Range Description DCF Integration Cassandra Compliant
1.0.0.x Initial version No Yes
1.1.0.x New firmware version 40 No Yes

Product Info

Range Supported Firmware Version
1.0.0.x version 29
1.1.0.x version 40

Installation and configuration

Creation

SNMP Main Connection

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP Connection:

  • IP Address/host: The polling IP of the device, e.g., 10.145.1.12.

SNMP Settings:

  • Port number: The port of the connected device, by default 161.
  • Get community string: The community string required to read from the device. The default value is public.
  • Set community string: The community string required to set to the device. The default value is public.

Usage

General Page

This page displays system parameters, such as SNMP Mode, Management Mode, Working State, Data Availability, System Alarm, Up Time, Maximum Severity, Firmware Bank Incoherence, Operating Mode and Trap Dispatching.

The Input General Status page button displays the general status information, including the External Reference, 10 MHz Reference, Hitless Switch Mode, Input Module Status, GPS Absent, PPS Absent, Clock Reference, Auto Switch Ref Presence, PPS Max Difference, PPS Difference and PPS Compare Warning.

The Input Trap Mangmt page button displays the trap configuration parameters, such as SW Hitless Trap, Alm Trap, On-Air Trap, Int PPSAbsent Trap, Ext PPSAbsent Trap, Ext10 Mhz Absent Trap, Module Status Trap and Summary Alm Trap.

The System Information page button displays the Firmware Version and other firmware information, including the Firmware Code, Firmware Release and Firmware Build.

Transmitter Overview

This page displays operative configuration parameters and power measurements, such as Nominal Power, Forward Power, Forward Power dBm, Reflected Power, Tx Forward Power and Tx Forward Power dBm.

The configuration options include the Output Channel Frequency, Transmitter Mode and System Struct Type.

Transmitter Configuration

On this page, you can configure transmitter settings and power settings, such as System Equipment Type, Power Thresholds, Input Channel Frequency, Output Channel Frequency and Channel Offset.

There are six page buttons available, which provide access to parameters related to ISDB-T, SFN, Tx Command, Tx Trap Mngmt, Tx Precorrection and Tx Input General Status.

Transmitter GPS

This page displays all GPS-related parameters:

  • GPS Units
  • GPS System Status
  • GPS Info Table
  • GPS Status Table
  • GPS Alarms Table
  • GPS Configuration Table

Repeater Configuration

This page displays parameters such as the Repeater Mode and Selectivity Delay. In the Echo Canceller section, you can find parameters such as the Echo Window, Echo Delay, Multipath Echo Window and Multipath Window Type.

It is also possible to configure the Repeater Activation, Repeater Standby and Lockout Reset.

Note: All of the parameters on this page will appear as N/A if the Transmitter Mode (on the "Transmitter Overview" page) is set to DVBT2.

RBL Configuration

This page displays DVBT2 Configuration, Alarm and Transmitter Receiver Status parameters.

Configuration options include DVBT2 Network Mode, Bandwidth, Transmission ID, MI Control Mode, Cell ID, Network ID, T2 System ID and Configuration Coherency.

Alarms include DVBT2 Delay Offset Alarm, RT Lock and Input Module Status.

Other transmitter receiver status parameters include Profile, L1 Post Constellation, IFFT, Guard Int, Pilot Pattern, MISO, T2 Frame Number, Data Number, P1 Detected, Lock L1 Pre, Lock L1 Post, Lock DMD, Offset, MER, SNR and BER (pre LPDC).

Note: All of the parameters on this page will appear as N/A if the Transmitter Mode (on the "Transmitter Overview" page) is set to REPEATER.

RBL Input Management

This page includes source selection, configuration and status parameters related to the input of the device. These are only relevant when the device is in RBL Mode.

Parameters include: Input Switch Mode, Input Selection, Input on Air, ASI Output Source, GBE Sources, External Reference, 10 MHz Reference, Hitless Switch Mode, GPS Absent alarm, PPS Absent alarm, 10 MHz Reference Absent alarm.

Note: All of the parameters on this page will appear as N/A if the Transmitter Mode (on the "Transmitter Overview" page) is set to DVBT2.

Gap Filler Configuration

This page includes configuration options, power options and alarm events that are only relevant when the device has been placed in Gap Filler Mode.

Options include GF Nominal Power, Channel Frequency, Repeater Channel Offset, Repeater Low Power Warning Threshold, Repeater Reflected Power Alarm Threshold, Repeater Selectivity Delay, Gap Filler Repeater Mode and GF Input Channel Frequency.

Alarm events include Management Mode, Working State, Repeater Status, Low Power Warn, Low Power Alarm, Reflected Power Warn, Reflected Power Alarm, Lockout Alarm, Interlock Alarm, Squelch, Out Fifo Alarm, Echo Canceller Warn, Lock Warn, Input Over Power Alarm and Input Low Power Alarm.

Forward Power and Reflected Power measurements are also included.

Finally, the page also contains the Echo Canceller, Commands and System Information page buttons.

Note: All of the parameters on this page will appear as N/A if the Transmitter Mode (on the "Transmitter Overview" page) is set to DVBT2.

Alarms

This page displays all alarm-related parameters, such as:

  • Low Power Warning
  • Low Power Alarm
  • Interlock Alarm
  • Internal PPS
  • Hardware Status
  • Etc.

Webpage

This page displays the webpage of the device. Note that the client computer has to be able to access the device, as otherwise it will not be possible to open the web interface.

Improve this page