SatService sat-nms MNC
With this connector, you can gather and view information from the device SatService sat-nms MNC and from the devices connected to it.
About
This connector is used to gather information from the SatService sat-nms MNC device, as well as any connected devices.
The connector displays several tables with general information for each device type.
Version Info
| Range | Description | DCF Integration | Cassandra Compliant |
|---|---|---|---|
| 1.0.0.x | Initial version | No | Yes |
| 1.0.1.x [SLC Main] | New range without DVEs | No | Yes |
Product Info
| Range | Supported Firmware Version |
|---|---|
| 1.0.0.x | Unknown |
| 1.0.1.x | Unknown |
Exported connectors (only for range 1.0.0.x)
| Exported Connector | Description |
|---|---|
| SatService sat-nms MNC - Antenna Controllers | Antenna controller devices |
| SatService sat-nms MNC - Tracking Receiver | Tracking receiver devices |
| SatService sat-nms MNC - Power Amplifiers | Power amplifier devices |
| SatService sat-nms MNC - EIRP Controllers | EIRP controller devices |
| SatService sat-nms MNC - Block Up Converters | Block up-converter devices |
| SatService sat-nms MNC - Up Converters | Up-converter devices |
| SatService sat-nms MNC - Down Converters | Down-converter devices |
| SatService sat-nms MNC - Test Loop Translators | Test loop translator devices |
| SatService sat-nms MNC - Uplink Power Controls | Uplink power control devices |
| SatService sat-nms MNC - Deicing Controllers | Deicing controller devices |
| SatService sat-nms MNC - Dehydrators | Dehydrator devices |
| SatService sat-nms MNC - Weather Monitors | Weather monitor devices |
| SatService sat-nms MNC - Wave Guide Switches | Wave guide switch devices |
| SatService sat-nms MNC - General Switches | General switch devices |
| SatService sat-nms MNC - Protection Switches 11 | 1-1 protection switch devices |
| SatService sat-nms MNC - Protection Switches 1N | 1-N protection switch devices |
Installation and configuration
Creation
SNMP Main Connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device.
SNMP Settings:
- IP port: The IP port of the device.
- Get community string: The community string used when reading values from the device, by default public.
- Set community string: The community string used when setting values on the device, by default private.
Usage
General
This page displays general information about the main device, such as the System Description, System Name, System Uptime, System Location, etc.
Devices
This page displays a table with all the devices attached to the main device.
Antenna Controllers
This page displays a table with all the antenna controllers.
Tracking Receivers
This page displays a table with all the tracing receivers.
Power Amplifiers
This page displays a table with all the power amplifiers.
EIRP Controllers
This page displays a table with all the EIRP controllers.
Block Up Converters
This page displays a table with all the block up-converters.
Up Converters
This page displays a table with all the up-converters.
Down Converters
This page displays a table with all the down-converters.
Test Loop Translators
This page displays a table with all the test loop translators.
Uplink Power Controls
This page displays a table with all the uplink power controls.
Deicing Controllers
This page displays a table with all the deicing controllers.
Dehydrators
This page displays a table with all the dehydrators.
Weather Monitors
This page displays a table with all the weather monitors.
Waveguide Switches
This page displays a table with all the waveguide switches.
General Switches
This page displays a table with all the general switches.
1-1 Protection Switches
This page displays a table with all the 1-1 protection switches.
1-N Protection Switches
This page displays a table with all the 1-N protection switches.
Fiber Optic Links
This page displays a table with all the fiber-optic links.
Power Supply Units
This page displays a table with all the power supply units.
Notes
Note on 1.0.0.x
Exercise caution when using the 1.0.0.x range, as it can occur that elements with duplicated names are created, which can cause major issues in DataMiner.
Note on 1.0.1.x
For the 1.0.1.x range, you must either apply alarm monitoring on the Devices table or on the remaining tables, in order to prevent double alarms.