Sencore MRD 6000
The MRD 6000 decodes and outputs 4K/UHD video with dual audio and includes core features required in professional video delivery networks such as MPEG/IP I/O, DVB-S/S2/S2X satellite inputs, QAM/VSB RF receiver, DVB-T/T2, C/C2, ISDB-T inputs, BISS descrambling, and dual DVB-CI CAM slot options.
This connector allows you to monitor and configure several aspects of the device: the inputs, the descrambling, the service or PIDs selection for decoding, and the outputs.
About
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x | Initial version | - | - |
| 1.1.0.x | New firmware | - | - |
| 1.1.3.x [SLC Main] | Display key changed and Low and High tag added to several parameters | - | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | 4.1.0 |
| 1.1.0.x | 4.2.0.RC4 |
| 1.1.3.x | 4.2.0.RC4 |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | Yes | - | - |
| 1.1.0.x | No | Yes | - | - |
Configuration
Connections
SNMP Main Connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP or URL of the destination.
- IP port: The IP port of the destination.
SNMP Settings:
- Get community string: The community string used when reading values from the device (default: public).
- Set community string: The community string used when setting values on the device (default: private).
Initialization
No extra configuration is needed.
Web Interface
The web interface is only accessible when the client machine has network access to the product.
How to use
The element created with this connector consists of the pages listed below.
General
On this page, you can find general information about the device, including License Options, Sensor information, and Power Supply information.
Input
On this page, the available input sources are listed in the TS Input Source Table.
The page also displays the Input Table, which contains the selected Primary and Backup Input Source. To configure these two parameters, you must enter the ID of the input sources in the Primary Source and Backup Source columns of the table. (The ID is available in the TS Input Source Table). Also in the Input Table, you can make the device switch between the Backup or Primary input by pressing the Switch button.
Conditional Access
This page allows you to view the status and configure the BISS descrambling engine and the CAM.
Decoding
On the decoding page, you can configure the PIDs or service of the MRD 6000 decoding.
Baseband Processing Video
This page contains the Video Output Table, where you can for example configure the format of the video. To do so, change the Format Mode to Manual and then enter the ID of the format you want in the Manual Format column. The IDs of the formats are listed in the Format Table on this same page.
It is also possible to configure the Aspect Ratio and Overlay here.
Baseband Processing Audio
This page displays the Audio Service Table, where you can for example configure the Operating Mode, Processing Mode, and Downmix of the audio.
Baseband Output Video
On this page, you can configure the HD-SDI, SD-SDI, UHS-SDI, and Composite output formats of the MRD 6000.
Note that the composite video output is only active if the output video format is SD (720x480i, 720x576i). For the other selected formats, there is no output from the composite video BNC jack. The video format selection determines which of the SDI output jacks is actively outputting.
Baseband Output Audio
On this page, you can configure the SDI, AES, and analog outputs of the MRD 6000.
Output
This page contains the TS Output Source Table, which lists the available outputs. The state of each output can be configured in the table.
MPEG/IP
On this page, you can configure relevant information about the MPEG/IP input and output.
DVB-S2
On this page, you can configure settings related to the DVB-S2 input.
ASI
On this page, you can configure settings related to the ASI input and output.
VSB
On this page, you can configure settings related to the VSB input.
Turbo PSK
On this page, you can configure settings related to the Turbo PSK input.
DVB-T2 and ISDB-T
On this page and its subpages, you can configure settings related to the DVB-T/DVB-T2/DVB-C/DVB-C2/ISDB-T inputs.
DVB-S2X
On this page, you can configure settings related to the DVB-S2X input.