Snell Wilcox IQHIP10
The Snell Wilcox IQHIP10 is a multiplexer for audio streams.
About
The connector allows the management of the Snell Wilcox IQHIP10 using a smart-serial connection.
Version Info
| Range | Description | DCF Integration | Cassandra Compliant |
|---|---|---|---|
| 1.0.0.x | Initial version | No | Yes |
| 1.0.1.x | DCF Implementation | Yes | Yes |
Product Info
| Range | Supported Firmware Version |
|---|---|
| 1.0.0.x | V167 |
| 1.0.1.x | V167 |
Installation and configuration
Creation
Serial [Main] connection
This connector uses a serial connection and requires the following input during element creation:
SERIAL CONNECTION:
Interface connection:
- IP address/host: The polling IP of the device (e.g., 192.168.14.15).
- IP port: The IP port of the device (e.g., 2050).
- Bus address: Used to fill in the Unit Address and the Unit Port (e.g., 10*.04* is for Unit Address 0x10 and Unit Port 0x04).
Usage
Connection Info
The Connection Info contains an overview of the session status such as Session Status, Assign Session Number, Local Session Number, Simulated RollCall Response, Card User Name, Unit Adress and Unit Port. There is also a Display with a overview of the unit status and a Force
Region Detectors
This page contains the Regions configuration, in the main page you can disable or enable, Region 1 or Region 2. It is possible to configurate the size of the window or activate Full Screen. There are also four buttons on the right Black Region, Blackish Region, Freeze Region and Stillish Region.
Black Region
In here you can check the Alarm and define some thresholds such has Black Fail, Black Warning and Black Hail Hold.
Blackish Region
This page has the alarm state and some threholds can also be configured.
Freeze Region
The main difference between previous pages is that the Freeze Tolerance can also be configured.
Stillish Region
The last page is similiar to the other three, but here is possible to configure the Stillish Max Threshold.
Input/Output/Pattern
Here it is possible to enable or disable the Pattern, Pattern Scroll, Pattern on Input Error and Pattern Type. The mute of the Output can also be configured on Input Error or by user's will.
Video Monitor
This page allows the configuration of the Average Picture Level Alarm, RGB Legalizer and Logging Threshold. There are two button which open a pop up where the Luma and Chroma can be configured.
Closed Captions
The Close Captions allows to check the Close Caption CEA-608-B, Close Caption CEA-608-B Title 1 and Title 2, CC CEA 708 B Field 1 and Field 2. Is is also possible to check and configure some Temporal Control parameters page gives an overview of the audio controls over the group 1.
Ancillary Data
This page gives an overview of the Ancillary parameters, such has Time Code Fileds, VITC fieldsover the group 2, Packet Detection.
Wide Screen Signalling
This page gives an overview of the Wide Screen Signalling, VI state and AFD (SMPTE 2016).
Audio Data Page
This page gives an overview of the audio data such has Data Type and Bit Depth for all sixteen Channels and each pair of channels.
Audio Level Detectors
In this page it is possible to copy the Audio Level Detectors from one channel to another. There four buttons each one opens a pop up to configure the Overload Detector, Quiet Detector, Loud Detector and Silence Detector.
Audio Level Indicators
The Audio Level Indicators allows to enable or disable the indicators for each sixteen channels.
Clipping Detector
This page contains the clipping alarms for all the sixteen channels.
Audio Likeness
This page gives an overview of the Likeness for each of the four detectors.
UMID
This page shows all the information about UMID and allows to configure the UMID generator.
PID
This page shows all the information about Program ID and allows to configure the Program ID generator.
Alarm Enable Summary
Here you can enable or disable all the alarms existing in previous pages such has channels, Regions, Luma, Chroma, etc...
Memory 1-16
This page Shows all sixteen memories and allows to save them.
Setup
Here is shown all the information from the device such has Serial, PCB, Build, Firmware. It is also possible to force a restart on the system and a factory reset.
On Screen Display
In this page it is possible to enable or disable all four outputs, configure and check the OSD state, Window Size, Caption, RGB Legalizer Range, Incoming and Outgoing PID.
Logging Misc
The Logging Misc allows to enable or disable the logging, but also see the value of parameters such has Hardware Version, Caption1 and 2, RearStatus, Power Usage.
Logging Input
The Logging Input allows to enable or disable the logging, but also see the value of parameters such has Input Name, Input State, Input Type, CRC, EDH.
Logging Region 1
The Logging of Region 1 allows to enable or disable the logging, but also see the value of parameters such has Black, Blackish, Freeze, Stillish.
Logging Region 2
The Logging of Region 2 allows to enable or disable the logging, but also see the value of parameters such has Black, Blackish, Freeze, Stillish.
Logging Inp 1 Monitor 1
The Logging of Input 1 Monitor 1 allows to enable or disable the logging, but also see the value of parameters such has Hyperion, Close Caption State, Close Caption Type and Close Caption Title.
Logging Inp 1 Monitor 2
The Logging of Input 1 Monitor 2 allows to enable or disable the logging, but also see the value of parameters such has Hyperion, Y Bit Depth, C Bit Depth, CA State, CA System, etc.
Logging Input 1 WideScreen
The Logging of Input 1 WideScreen allows to enable or disable the logging, but also see the value of parameters such has WideScreen State, Aspect, ETSI Data, VI State, VI Aspect, etc.
Logging Input 1 Audio State
The Logging of Input 1 Audio State allows to enable or disable the logging, but also see the value for all the channels.
Logging Input 1 Audio Type
The Logging of Input 1 Audio Type allows to enable or disable the logging, but also see the value of the audio type for all the channels.
Logging Input 1 Dolby E State
The Logging of Input 1 Dolby E State allows to enable or disable the logging, but also see the value of the audio each audio pair, having a total of eight.
Logging Input 1 Audio Bit Depth
The Logging of Input 1 Audio Bit Depth allows to enable or disable the logging, but also see the value of the bit depth for all the sixteen channels.
Logging Input 1 Audio Level
The Logging of Input 1 Audio Level allows to enable or disable the logging, but also see the value of the audio level for all the sixteen channels.
Logging Input 1 Audio Clipping
The Logging of Input 1 Audio Clipping allows to enable or disable the logging, but also see the value of the audio clipping for all the sixteen channels.
Logging Input 1 Audio Likeness
The Logging of Input 1 Likeness allows to enable or disable the logging, but also see the value of the all four detectors.
Logging Input 1 UMID/PID
The Logging of Input 1 UMID/PID allows to enable or disable the logging, but also see the value of the the UMID and PID for the input.
Logging Output 1 UMID/PID
The Logging of Output 1 UMID/PID allows to enable or disable the logging, but also see the value of the the UMID and PID for the output.
Rolltrack Page
The Rolltrack page provides a simple command interface for sending unconnected Rolltrack commands to any Rollcall compatible unit on the network. The following parameters are displayed: Disable All, Rolltrack Index from 1 to 16, Rolltrack Source, Rolltrack Address, Rolltrack Command, Rolltrack Sending and Rolltrack Status.
Web Interface Page
This page allows the user to access the original web interface of the device. The client machine has to be able to access the device. If not, it won't be possible to open the web interface.
DCF Implementation
The input connects to all the outputs at startup, all the connections are static only allowing to disconnect or connect to an output.