Snell Wilcox IQMCC3000-1B3
The Snell Wilcox IQMCC3000-1B3 is a motion-compensated frame rate converter that provides multi-rate and format conversion for 3 Gbps SDI and HD-SDI digital video signals. The Snell Wilcox IQMCC3000-1B3 connector is the solution designed to monitor this converter.
About
With this connector, you can manage the Snell Wilcox IQMCC3000-1B3 device using a smart-serial connection.
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [SLC Main] | Initial version | - | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | 4.15.3 |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | Yes | - | - |
Installation and configuration
Creation
Serial Main Connection
This connector uses a serial connection and requires the following input during element creation:
SERIAL CONNECTION:
Interface connection:
- IP address/host: The polling IP of the device, e.g., 192.168.14.15.
- IP port: The IP port of the device, e.g., 2050.
- Bus address: The unit address and the unit port. For example, for unit address 0x10 and unit port 0x04, specify 10.04.
Usage
General
This page displays information related to the unit itself and to the session status, such as Unit Name, Card User Name, IP Share Port, IP Bridging Port, Session Status and Assigned Session Number.
Input
This page shows information about input source parameters and allows you to select the input for this converter.
Output-Ch1
On this page, you can view and configure output parameters for channel 1, such as Output Standard, Force Freeze, Embedded Audio, Luma Clipper and Default Output.
Video-Ch1
On this page, you can view and configure video parameters for channel 1, such as Master Gain, Contrast, Black Level, Noise Rejection, Nonlinear Enhancer and Vertical Frequency Band.
Convert-Ch1
This page provides an overview of the converter parameters for channel 1, such as Up Conversion, Motion Processing, Input Cadence and Output Cadence.
ARC & Sidebar Keyer-Ch1
On this page, you can view and configure ARC & Sidebar Keyer parameters for channel 1, such as Post Scaling Control, Arc Memories, Scaler Config and Output Signaling Config.
Audio Routing-Ch1
On this page, you can configure audio routing parameters for channel 1 for all eight process pairs.
Audio Shuffle-Ch1
On this page, you can configure audio parameters for channel 1 for all eight output pairs.
Audio Control-Ch1
On this page, you can configure audio parameters for channel 1, such as Tone Frequency, Dolby E Alignment Offset, and Delay. It is also possible to configure the gain for each of the eight output pairs here.
Genlock
On this page, you can configure the Vertical and Horizontal Timing for each source.
Timecode-Ch1
On this page, you can view and configure timecode parameters for channel 1, such as Source, Mode, On Timecode Loss, Timecode Entry and 29.94FPS.
Metadata-Ch1
On this page, you can view and configure parameters for channel 1, such as Closed Captions, Teletext, SMPTE RDD08/SMPTE 2031 VANC PKT and SMPTE 2020 Output.
Ancillary Bridge-Ch1
On this page, you can configure several ancillary data stores parameters related to channel 1, from block 1 to 7.
Rolltrack
This page provides a simple command interface for sending unconnected Rolltrack commands to any Rollcall-compatible unit in the network. The following parameters are displayed: Disable All, Rolltrack Index, Rolltrack Source, Rolltrack Address, Rolltrack Command, Rolltrack Sending and Rolltrack Status.
Memories
This page shows all 32 memories and allows you to save them.
Misc. Logging
On this page, you can enable or disable the logging for miscellaneous parameters, such as Serial Number, Up Time and Power Usage.
Video Input Logging
On this page, you can enable or disable the logging for video input parameters, such as Input 1 Type, State and Standard.
Output Logging
On this page, you can enable or disable the logging for output parameters such as Output Type, State and Standard.
O/P Audio State Ch1 Logging
On this page, you can enable or disable the logging for Output Embedded State type parameters.
O/P Audio Type Ch1 Logging
On this page, you can enable or disable the logging for Output Embedded Audio type parameters.
Setup
This page displays information regarding setup parameters, such as the Software Version, Rear ID, Serial Number and Build Version.
Web Interface
This page can be used to access the web interface of the device. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface