Snell Wilcox IQUDC30
The Snell Wilcox IQUDC30 connector monitors and configures the IQUDC30 converter.
About
The connector polls all parameters once after startup. After this, parameter updates depend on event messages generated by the device when a parameter changes. However, it is possible to manually trigger the polling of all parameters with the Force Poll button on the General page.
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [SLC Main] | Initial version | - | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | V5.7.9 |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | Yes | - | - |
Installation and configuration
Creation
Serial Main Connection
This connector uses a single smart-serial connection and requires the following input during element creation:
SERIAL CONNECTION:
Interface connection:
- IP address/host: The polling IP of the device.
- IP port: The IP port of the device, by default 2050.
- Bus Address: The bus of the card on the chassis. The default value is UU.PP (Hex). This shows the expected structure of the address, where UU is the chassis ID, and the PP is the card position, both in hex.
Usage
General
This page displays general information about the device, such as the Versions, Serial Number, Build, IP Share/Bridging Port and more. It also includes the Information Display, as well as the following buttons:
- Factory Defaults: Sets the device back to the factory defaults.
- Default Settings: Sets the device back to the default settings.
- Restart: Restarts the device.
- Force Poll: Polls the device again.
- Connection Info: Opens a subpage with various parameters related to the serial connection, including the assigned session number, local session number and session status. It also includes the Simulated RollCall Response, which allows you to set a custom response that will be handled by the connector as if it were received by the device.
- IQOPTM: Opens a subpage with various IQOPTM toggle buttons.
Input
This page displays the Input Source, SDI 1 Status, SDI 2 Status and Current Input Standard.
Output
This page contains output-related parameters, such as Output Format, Default Field Rate, Current Output Standard, SD Half Line and more. It also contains Caption controls (Entry, Scroll, and Status).
Video
This page contains video-related parameters, such as Gamma, Saturation, Contrast, Black Level and YC Offset. It also contains Nonlinear Enhancer controls and Conversion Aperture Controls, as well as the Preset button, which sets all current settings as a preset.
Convert
This page contains converter-related controls, such as Clean Edge Upconversion, Still Process, Enhanced Film Mode, 2:3 Source, Film Cadence and more.
ARC and Sidebar Keyer
This page contains various ARC and sidebar parameters, such as Sync Mode, Signaling Detected status, VI controls and L23 controls.
It also contains the following page buttons:
- Force Mode: Displays the SMPTE 2016, RP186, AFD and ETSI controls.
- Input Config: Displays the Input Signaling source, SD Input Format and Force Input Format.
- Output Config: Displays the Conversion Scaling and SD Output Format.
- Post Scaling Control: Displays the Post Scaling Status, as well as controls such as size, aspect, pan and tilt.
- Presets: Displays the SD Input is 702, SD Output is 702, SD Cross Conversion, Up Conversion and Down Conversion controls.
Audio Routing
This page contains a Source control for each process pair, and displays the Status for each process pair and embedded pair.
Audio Shuffle
This page contains the control, source, and invert phase controls of each pair, left and right, and displays the status of each output pair.
Audio Control
This page contains the gain and delay controls for all 8 left and right pairs, and displays the total delays for all of the pairs. It also contains the global total delays for audio and video.
Genlock
This page contains the Horizontal Timing, Vertical Timing, Timing Status and Source Ch1.
Timecode
This page contains the source controls for both SD and HD, as well as various timecode-related parameters, such as On Timecode Loss, Processing Mode, Timecode Entry, VITC, Output Lines, and 29.94 fps.
Metadata
This page contains the closed caption and CEA-708/CEA-608 controls.
GPI/O
This page contains controls to set the GPIO modes to either input or output, as well as to set each GPI/GPO channel.
RollTrack
This page contains information about the RollTrack, such as the index, source, address, command, status, and sending status.
Memories
On this page, you can select a memory (1-16) and edit its name, recall a previous memory (if available), and also view the Last User Memory.
The page includes the following buttons:
- Save Memory: Saves the current memory name.
- Clear Memory: Clears the current memory.
Misc Logging
This page displays information about general parameters (Serial Number, Up Time, Power Usage, Build). It also contains toggle buttons that allow you to enable or disable the logging of this information.
Video Input Logging
This page displays information about video inputs 1 and 2 (Type, State, Standard). It also contains toggle buttons that allow you to enable or disable the logging of this information.
Output Logging
This page contains information about the output (Type, State, Standard). It also contains toggle buttons that allow you to enable or disable the logging of this information.
Output Audio State Logging
This page displays information about each of the 8 output embedded pair states. It also contains toggle buttons that allow you to enable or disable the logging of this information.
Output Audio type Logging
This page displays information about each of the 8 output embedded pair types. It also contains toggle buttons that allow you to enable or disable the logging of this information.
Web Interface
This page displays the web interface of the device. Note that the client machine has to be able to access the device, as otherwise it will not be possible to open the web interface.