Thales TNM-7122-D
This is an SNMP connector that can be used to monitor and configure Thales TNM-7122-D equipment.
About
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [Obsolete] | Development version. | - | - |
| 1.1.0.x [Obsolete] | Development version. | - | - |
| 1.0.5.x | Limited connector version for units with firmware version 01.05x.xx. | - | - |
| 2.0.0.x | Initial release range. | - | - |
| 2.0.1.x [SLC Main] | Initial release range with fix to avoid overwritten active alarms caused by the device itself. | 2.0.0.x | The Active Alarms table with PID 6000 is no longer available. Its data will now be shown in a new Active Alarms table with PID 6500. This table has a new primary key and display key. The primary key is the hashed concatenation of the module, the input, the description and the date. |
| 3.0.0.x [Obsolete] | SNMP2 version based on range 2.0.0.x. This range is no longer maintained, as it is now possible to select the SNMP version in the element configuration. Use range 2.0.1.x instead. | 2.0.0.x | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | - |
| 1.1.0.x | - |
| 1.0.5.x | 01.05x.xx |
| 2.0.0.x | - |
| 2.0.1.x | - |
| 3.0.0.x | - |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | Yes | - | - |
| 1.1.0.x | No | Yes | - | - |
| 1.0.5.x | No | Yes | - | - |
| 2.0.0.x | No | Yes | - | - |
| 2.0.1.x | No | Yes | - | - |
| 3.0.0x | No | Yes | - | - |
Configuration
Connections
SNMP Main Connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device.
SNMP Settings:
- IP port: The IP port of the device.
- Get community string: The community string used when reading values from the device, by default public.
- Set community string: The community string used when setting values on the device, by default private.
Web Interface
The web interface is only accessible when the client machine has network access to the product.
How to Use
The element consists of the data pages detailed below.
General
This page displays general information such as the Vendor and Serial Number. Via page buttons, you can access subpages related to Equipment Features and configurable Relays.
Inputs-Outputs
This page displays the Switch State, Input 1, Input 2 and Output status.
Tests Level 1/2/3/Advanced
These pages contain tables with test information.
Streams
This page displays information on the transport streams.
Services
This page displays information on Services and Services Checks.
PIDs
This page contains information on PIDs. It also allows you to Confirm all PIDs and Remove N/A PIDs. Via page buttons, you can access the PIDs Bandwidth and PIDs in Service subpages
Overview
This page contains a tree control that displays information about inputs.
Output Streams
This page displays information on the output transport streams.
Output Services
This page displays information on output services. You can remove services that are no longer available.
Output PIDs
This page displays information on output PIDs. It also allows you to Confirm all PIDs or Remove N/A PIDs. Via page buttons, you can access the Output PIDs Bandwidth and Output PIDs in Service subpages.
Output Overview
This page contains a tree control with information about outputs.
Alarms
This page displays the Active Alarms and Closed Alarms tables.
Configurations
This page displays configuration version information. You can retrieve a configuration from the list of available configurations. This will display the information related to Smart Switcher, System and Inputs configuration.
Via page buttons, you can access the following subpages:
- System: Displays various system configuration parameters.
- Input: Displays the Input Configuration table.
- Smart Switcher: Displays various smart switcher configuration parameters.