Tryo Communications SDA+15W Outdoor

The Tryo Communications SDA+15W Outdoor is used as a transmitter that transmits electromagnetic waves carrying messages and signals.

About

This connector polls data from the Tryo Communications SDA+15W Outdoor via SNMP and displays the information on multiple pages with various tables and standalone parameters. Some parameters can be used to update data within the device by means of an SNMP set. The connector also handles traps, by parsing a trap for the OID of the parameter that caused the trap and repolling the parameter for an updated value.

Version Info

Range	Key Features	Based on	System Impact
1.0.0.x [SLC Main]	Initial version	-	-

Product Info

Range	Supported Firmware
1.0.0.x	1.1

System Info

Range	DCF Integration	Cassandra Compliant	Linked Components	Exported Components
1.0.0.x	No	Yes	-	-

Installation and configuration

Creation

SNMP Main Connection

This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:

SNMP CONNECTION:

IP address/host: The polling IP of the device.

SNMP Settings:

IP port: The IP port of the device, by default 161.
Get community string: The community string used when reading values from the device, by default public.
Set community string: The community string used when setting values on the device, by default public.

LITE Mode

LITE mode reduces the number of polled parameters of this protocol in order to save bandwidth over GSM connections. To enable this functionality, use the toggle button on the SNMP Config subpage.

The following parameters are polled in this mode: Frequency, Service Mode, Temperature Status, Modulator Internal Temperature, SWR Status, GPS Lock, User RF Status, Secondary Input Storage Time, Transit Delay, C/N Ratio, Carrier Status, Satellite Receiver Frequency, TS Bit-Rate, Number of Satellites, Number of Satellites in sight, RF User, Power and RF SWR.

Usage

MDVB General

This page displays general information about the device, such as the Manufacturer, Device Name and Device Type.

SNMP Configuration

This page allows you to view and configure SNMP settings, including the Read and Set Community and the LITE Mode.

Time and Date

This page corresponds to the Time and Date tab in the web interface, where you can configure the time and date of the device, as well as see the last time the device was synced.

SUMMIT General

This page displays general information about the SUMMIT of the device, such as the SUMMIT Version. It also allows you to set the Service Mode and RF User Setting.

SUMMIT Status

This page contains status information for the CPU, Driver and Exciter of the device.

Power Amplifier

This page contains status information for the Power Amplifier of the device.

System

This page contains status information on the overall condition of the system.

Configuration General

This page contains basic settings for the device, such as Precorrector Data, Starting Delay and Clock-Config PPS Edge.

Control Configuration

This page contains advanced settings for the device, such as Control Crest Factor, Gain Offset and Control RF Frequency.

DAB Configuration

This page contains configurable parameters for the DAB of the device, such as PPL Status, Input Switching Type and Input Stream Selection.

Satellite Receiver Configuration

This page contains configurable parameters for the Satellite Receiver, such as LNB Voltage, Demodulator Standard and TS PID.

EDI Configuration

This page contains configurable parameters for the EDI feature of the device, such as Reception Mode, Port and Receiver Latency.

Interface Configuration

Similar to the EDI page, this page contains configurable parameters for the interface of the device, such as Mode, DHCP and IP Address.

Status General

This page contains basic status parameters for the device, such as Hardware Version, Process Load and Internal PLL.

Monitoring Status

This page contains more advanced status parameters, such as Monitoring Crest Factor, AGC and Input Level.

EDI Status

This page contains status parameters for the EDI feature of the device, such as UDP Reception, Type and Reed Solomon.

DAB Status

This page contains status parameters for the DAB of the device, such as ETI Input, Input Packet and Header CRC.

Satellite Receiver Status

This page contains Satellite Receiver settings, such as Input RF Level, Symbol Rate and TS Bit-Rate

GPS Status

This page contains status parameters for the GPS feature of the device, such as Type, Antenna Status and Longitude.

RF Detector

On this page, you can view and configure parameters related to the RF Detector of the device.

SD General

This page contains two tables:

Power Amplifier Table: Displays the power amplifier status.
Measurement table: Displays measurements for different parameters of the device.

PAU General

This page contains the PAU General Table, with basic information about the PAU of the device.

Fan