Wellav UMH 160 T2
This connector can be used to monitor Wellav UMH 160 T2 devices. WellAV UMH 160 S2 and WellAV UMH 160 IP devices are monitored by a dedicated connector. An SNMP connection is used to successfully retrieve the device's information.
About
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [SLC Main] | Initial version | - | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | - |
System Info
| Range | DCF Integration | Cassandra Compliant | Linked Components | Exported Components |
|---|---|---|---|---|
| 1.0.0.x | No | No | - | - |
Installation and configuration
Creation
SNMP Main connection
This connector uses a Simple Network Management Protocol (SNMP) connection and requires the following input during element creation:
SNMP CONNECTION:
- IP address/host: The polling IP of the device.
SNMP Settings:
- Port number: The port of the connected device, by default 161.
- Get community string: The community string used when reading values from the device. The default value is public.
- Set community string: The community string used when setting values on the device. The default value is public.
Usage
Status
This page displays all status information for the Input Tuner, Input ASI, Input IP, Output ASI, Output IPs, and CI Slots.
Input Receiver
This page displays tuner-related information. There are parameters for both Tuner 1 and 2.
- Enable
- Mode
- Frequency
- Bandwith
- PLP Mode
- TS Standard
- ScanTS
Input ASI
This page displays ASI 1, ASI 2, and the TS Standard for both ASI 1 and 2. There is also a ScanTS button for both ASI 1 and 2.
Input IP
This page displays the following local connection and channel information for channel 1 and channel 2.
- Local IP Address
- Local Subnet Mask
- Local Gateway
- Local Speed Mode
- Local Mac
- Channel
- Source IP Address
- Source Port
- Protocol
- Enable Col Port Matching
- Enable Row Port Matching
- TS Standard
A page button opens the IGMP pages for Channel 1 and Channel 2. They display the IGMP Version, Auto Report, Filter, and IP Address.
Backup Setting
Here the Main and Backup Input StreamBackup Settings can be set, both for Stream 1 and Stream2.
Output Decoder
This page displays information related to the decoder, video, audio, subtitle, and teletext. The related tables display the indexes, names and PID.
Output ASI
This page displays the TS Source for ASI 1 and 2.
Output IP
This page provides the GbE Port Setting for the Main and Backup and the following IP information for two channels:
- Enable
- TS Source
- Protocol
- IP Address
- Port
- MAC
- Backup IP Address
- Backup Port
- Backup MAC
A button can be used to set the backup port the same as the main port.
CA
This page shows the CAM Max Bitrate and BISS related parameters: Mode, the BISS-1 and BISS-E Keys, and the BISS-E ID. The TS Sources are also displayed for both CAs.
Program Mux Setting
This page displays information related to the Mux 1, Mux 2, Tuner 1, Tuner 2, ASI 1, ASI 2, IP 1, and IP 2. The related tables display the indexes, names, and PID.
System
This page displays system information such as the IP Address, Subnet Mask, Gateway, as well as some Trap information. This page also contains a Reboot and a FactorySet button.
Alarm
This page displays six alarms: LNB Connection Short, Signal Unlock, CAM 1 and CAM 2 Communication Error, and Descrambling.
Web Interface
On this page, you can view the web interface of the device. However, the client machine has to be able to access the device. Otherwise, it will not be possible to open the web interface.