Ross Video General Frame - Cobalt Digital 9922
This is an exported connector that displays information regarding the 9922-2FS card. It is automatically generated by the parent connector Ross Video General Frame, range 1.0.0.x.
SNMP polling is used to retrieve the device information.
Note that the layout of this connector is similar to that of the web interface.
About
Version Info
| Range | Key Features | Based on | System Impact |
|---|---|---|---|
| 1.0.0.x [SLC Main] | Initial version | - | - |
Product Info
| Range | Supported Firmware |
|---|---|
| 1.0.0.x | - |
Configuration
Creation
This connector is used by DVEs that are automatically created by the parent element. No user input is required.
Usage
Card Info
This page displays the general parameters for card 9922: Product, Manufacturer, Software, Hardware, Firmware, etc.
Status
This page displays the general status parameters for card 9922, including the status of all inputs and GPIs, as well as the Temperature, Input Voltage, Power, etc.
Admin
On this page, you can find the global card operating status. You can also configure the card communication IP address.
Alarm
This page displays alarms that are related to Loss of Signal, Frozen Video, Path 1 Audio, Black Video, and Loss of Reference. It also displays the Alarm History, which has a maximum of 8 entries.
COM Setup
This page allows you to configure the COM, including Mode and Routing.
Event Setup
On this page, you can view the Event Setup History, configure the Event Timer, check the event status in the Event Status table, and configure an event with the Event Setup Mixed table.
User Log
This page displays User Log Details with the time of the log, the event, and the type of the log. You can clear the log using the Clear User Log button.
Input Video
This page displays the status of the input video for path 1 and path 2, including the SDI status. You can also configure the Input Source of path 1 and 2.
Output Video
On this page, you can configure the SDI Out and the Analog Video settings for the card.
Framesync - Path 1 & Framesync Path 2
These two pages allow you to configure several settings for the frame sync for path 1 and path 2, including Lock Mode, Output Mode, Test Pattern, etc.
You can also configure the Lock Status, Vertical Lines, and Horizontal Us settings.
Audio Delay
In the tables on this page, you can configure the audio delay of each channel for path 1 and path 2.
Dolby E Alignment
On this page, you can configure settings for the Dolby E alignment for path 1 and path 2.
Input Bus Path
On this page, you can configure the input bus for each channel of path 1 and path 2.
Input Flex
On this page, you can configure the input flex for each channel of path 1 and path 2.
Input Audio Status - Path 1 / Input Audio Status - Path 2
On these two pages, you can view the Emb status of the input audio, as well as configure AES and Analog settings for both path 1 and path 2.
Embedded Output
This page is used for configuring the embedded output for both path 1 and path 2. You can enable the groups and configure embedded output for each channel of both paths.
Downmixer
This page provides different settings for the downmixer of path 1 and path 2, including different Channel Inputs and the Mix Ratio.
Output Flex Mix
This page allows you to select the audio source for each flex audio output channel. It also provides Gain, Phase Invert, and Muting controls and Peak Level Meters for each output channel.
AES Output
This page allows you to select the audio source for each AES audio output channel. It also provides Gain, Phase Invert, and Muting controls and Peak Level Meters for each output channel.
Analog Output
This page allows you to select the audio source for each analog audio output channel. It also provides Gain, Phase Invert, and Muting controls and Peak Level Meters for each output channel.
Output Video
This page contains the configuration for the Output Routing SDI Out (1 to 4).
Video Proc
On these pages, you can configure the following video proc settings for path 1 and 2, respectively: Luma Gain, Luma Lift, Color Gain, Color Phase, Gang Luma/Color Gain, and other Color Correction controls.
Ident 1 - Path 1 / Ident 2 - Path 1
These pages allow you to configure up to two ident text strings on output video for path 1.
Ident 1 - Path 2 / Ident 2 - Path 2
These pages allow you to configure up to two ident text strings on output video for path 2.
Timecode Burn - Path 1 / Timecode Burn - Path 2
These pages provide controls that allow you to configure a time code burn on output video for path 1 and 2, respectively.
Timecode - Path 1 / Timecode - Path 2
These pages provide controls that allow you to configure time code settings for path 1 and path 2.
Reticules - Path 1 / Reticules - Path 2
These pages allow you to add Safe Action and Safe Title overlays and other static markers to the output video image for path 1 and path 2, respectively.
Presets
On this page, you can configure different preset layers, load the specific preset for the card, and create and remove the preset for the card.
Reticules Advanced - Path 1 / Reticules Advanced - Path 2
These pages contain insertion and sizing controls for custom graticules and other markers. They also allow NTSC legacy 4:3 master reticule sizing for path 1 and 2, respectively.
Timecode - Path 1 / Timecode - Path 2
These pages provide time code data extraction from various sources and contain formatting and re-insertion controls for the insertion of the time code into the output video for path 1 and 2, respectively.
Closed Captioning
This page contains settings for the closed captioning for path 1 and path 2, respectively.
Moving Box
This page allows you to configure a moving box graphic overlay on the output video. Moving-box insertion can serve as a dynamic raster confidence check even in cases where the input video image is static or lost.
Wings
This page contains settings for the wings of the card for path 1 and path 2, respectively. This includes enabling or disabling the wings, configuring the Width Pixels and the Source, etc.
GPO Setup
On this page, you can set up the GPO for path 1 and path 2.
Ancillary Data Processing Path 1 & Ancillary Data Processing Path 2
This page shows the status of the ancillary data processing. You can also configure the data processing for each ADP Proc of path 1 and 2, including Setup Mode, Setup Did, Setup SDid, etc.
YC Alignment
This page contains settings for YC Alignment of path 1 and path 2